Welcome To Ebikes Online

How to service the hubs on your bike

How to service the hubs on your bike

Regular servicing can extend the life of your hubs

If your wheels feel rough when you spin them, it’s time to service the hubs on your bike.

Usually the problem will be caused by wear in your bearings or by the ingress of water and grime. Wheel bearings also do eventually wear out over time which will introduce play to the hub, allowing the wheel to rock side to side on its axle.

There are two types of bearings commonly seen in hubs – sealed (cartridge) bearings and non-sealed (cup and cone, or loose) bearings.

Regular servicing can extend their life, although they will eventually wear out to the point that they need to be replaced.

How to service bike hubs

How to service loose ball cup and cone hubs

You will need:

Tools required for loose ball hub servicing
Tools required for standard hub servicing.
BikeRadar
  • Cone spanners – usually 15 and 17mm
  • Grease
  • A magnetic hex screwdriver or pick
  • A chainwhip and cassette removal tool
  • Adjustable spanner
  • Degreaser
  • Paper cloth or clean rags

Step 1: Remove the locknuts

Undo the locknuts on the non-driveside
Undo the locknuts on the non-driveside.
BikeRadar

We are using a rear wheel, but the procedure is the same for a front.

For the rear, first remove the cassette from the freehub body.

Undo the lock nut on the non-driveside by using a cone spanner to hold the cone and another to undo the nut. Remove the locking nut and spacer by hand.

It’s a good idea to take note of the order in which the locking nut and any spacers are removed to ease re-assembly later – we recommend taking a photo on your phone.

Hold the lock nut on the drive side with one spanner, then undo the non-driveside cone with the other and wind it off by hand. You should now be able to remove the axle from the hub.

Step 2: Remove and clean the bearings

Remove the bearings and clean them using degreaser and rag
Remove the bearings, and clean them using degreaser and paper cloth.
BikeRadar

Carefully remove the bearings from the race – the tip of a magnetic screwdriver will help you to lift the bearings out.

You’ll now need to clean the bearings. Use a degreaser and some paper cloth, making sure you fully clean away all the old grease before proceeding.

Take a close look at the bearings, the cups (which are pressed into the hub) and the cones. If there’s any sign of wear on them, they’ll need replacing.

Note: The cups in Shimano, and many other clone hubs, are non-replaceable. If they have worn out, you will have to rebuild a new hub into your wheel. Campagnolo cups are replaceable.

Step 3: Re-grease the hub

Apply grease to the bearing race, then return the bearings to the hub
Apply grease to the bearing race, then return the bearings to the hub.
BikeRadar

Take some grease and apply a healthy dose to the bearing race in the hub.

You can now place the bearings into the grease which will help hold them in place. Again, a magnetic screwdriver makes this job much easier.

When all of the bearings are in place, you can then refit the axle and gently turn it to ensure they are installed correctly. Remove the axle then repeat the process on the other side.

Step 4: Refit the axle

How to service the hubs on your bike
Refit the axle into the hub.
BikeRadar

Now return the axle to the freehub side. Press it against the bearings and rotate it to check it’s seated correctly. Refit the cone to the non drive side of the axle and tighten it until contacts the bearings. It doesn’t need to be very tight – finger-tight will do.

You can then spin the axle to make sure it rotates cleanly. Give the axle a little wiggle to ensure you have eliminated any play.

You may need to adjust the tightness of the cone to stop any play or drag – if it’s too tight the hub will not spin freely. Conversely, if it’s too loose, there will be play in the axle.

This step takes a little trial and error, but don’t rush it as a poorly adjusted hub is likely to cause issues in the future.

Return the other nuts, spacers and seals to the non drive side of the axle, referring to your notes of which order they were removed in.

Then while holding the cone in place, use the other spanner to tighten it against the locking nut. It’s important to check the axle still rotates freely at this point as it’s very easy to tighten the cone also during this procedure.

Step 5: Refit the cassette

Finally, refit the cassette to the freehub body, replace the quick release skewer and return to the bike.

How to service sealed cartridge bearing hubs

Tools required

  • Multi-sized cone spanners: 13, 14, 15 and 16mm
  • Open-ended 15mm spanner
  • 5mm Allen keys
  • Solid rear axle
  • Nylon mallet
  • Small screwdriver
  • Bearing grease
  • Special tools or alloy tube to press the bearings

Step 1: Remove hub dust caps

Removing the dust caps may require a fair bit of force, so always use an allen key with a fresh head
Removing the dust caps may require a fair bit of force, so always use a hex key with a fresh head.
BikeRadar

The axle of your hub will likely have at least one end with a removable dropout guide or locknut that you’ll need to take off.

In most cases, this can be done by inserting a 5mm Allen key at both ends and turning anti-clockwise. You might have to put some muscle into it, so use a little cheater bar or a long hex key for this.

Keep track of any washers and their positions between the spacers and axle. The silver spacer doubles as both a dust cap and decorative element in most hubs. It might take some strength to pry off as it will likely be held in by a rubber O-ring between it and a groove on the axle.

Alternatively, some hubs (eg. Mavic) have a threaded cap to allow for bearing adjustment, so just unscrew these first. Others, such as Hope, simply use an interference fit cap. Refer to your manufacturer for exact instructions.

Step 2: Remove the old bearings

Always support the hub when removing bearings
Always support the hub when removing bearings.
BikeRadar

In order to remove the bearings, you’ll first need to support the hub in such a way that you won’t damage it. For example, you could use a delrin tube of the sort you can pick up (for a very reasonable price) from Hope.

An old solid axle makes an excellent bearing drift
An old solid axle makes an excellent bearing drift.
BikeRadar

You’ll need to strike a few sharp blows to get the bearings out, so a rubber mallet probably won’t do; a resin mallet or a hardwood block with a lump hammer are much better at delivering the force necessary to dislodge it.

Step 3: Remove the other bearing

The next operation removes the bearing which is left behind. Flip the wheel over and position the hub with the bearing facing down. Make sure the hub is sufficiently supported by the flange and there’s room for the bearing to come out.

Carefully position either the axle or a suitable drift tool (an aluminium tube or even an old solid axle with a cone or nut threaded partially onto it will do) and knock the bearing out with a few sharp blows. Be aware that you might have to hit it pretty hard if it’s a tight fit.

Clean the whole hub with a suitable degreaser and a rag, including the hub flanges around the spoke anchor points – you don’t want any debris to get into the bearing seat when refitting.

Inspect the flanges of the hubs, particularly around the spoke holes for cracks or corrosion. You’ll need a new hub or wheel if cracks are spotted.

Step 4: Press in the new bearings

Spread a light coating of grease on the outside and inside of the new bearings, on the inside of the hub shell and on the axle. If the grease is too thick between the bearing and the hub, it could prevent it from seating completely.

Some hubs may suggest you use a retaining compound, such as Loctite 641, or nothing at all – as always, refer back to your manufacturer for the correct advice.

 

It is worthwhile investing in a small bearing press for jobs like this
It is worthwhile investing in a small bearing press for jobs like this
BikeRadar

The new bearing should only be driven using the outer race of the bearing as striking the inner race is likely to cause damage to the small ball bearings inside the cartridge.

Use the old bearing or a socket of exactly the same diameter to drive the new bearing in. Keep in mind that the bearing races are made of hardened steel and are therefore potentially brittle. Wear protective goggles and make sure the contact area between the drift edge and the outer race edge is maximised by being perfectly aligned. You’ll know the bearing is seated when the blows suddenly firm up.

A bearing press is, by far, the best solution for this job, and is something well worth investing in.

Refit the axle, position the second bearing and then drive it in with a few blows.

Don’t allow the bearing to go in askew as attempting to force it in if it’s badly out of line will only get it jammed and make it harder to install. It’s also likely to create ridges that could prevent it from seating correctly, or could even damage the hub beyond repair.

Thread the dust caps back on with a little oil, then feel for that well earned, buttery smoothness.

 

Leave a Reply

Your email address will not be published. Required fields are marked *